Skip to content
Free NZ shipping over $99  ·  Flat rate $8.95  ·  Tauranga based, NZ owned
Click IT Store
Shop Account Cart

PBS-33B 12mm Momentary Push Button, Pre-Wired – Clearance – Red and black

PBS-33B 12mm Momentary Push Button, Pre-Wired – Clearance – Red and black to Pinterest (opens in a new window)
PBS-33B 12mm Momentary Push Button, Pre-Wired - Clearance - Red and black

Brand NZN Electronics CLICK IT SKU CLICK-IT-967653 Category Cables & Adapters

(0 reviews)

  • Brand NZN Electronics

Verified specifications

Brand
NZN Electronics

Taken from this product's published details. If something is not listed here, it has not been verified.

Ask AI about this product

Answers use this product's information and the store's details. If it cannot be confirmed, it will point you to our team.

Any language. Press Enter to ask

Frequently bought together

Bundle idea: this item plus 2 recommended accessory/accessories, $4.77 in total. Add each item to the cart below.

View full specs

Complete your setup

Overview

Clearance – final units. We are not restocking the pre-wired PBS-33B, so these last few are priced to clear. They are brand new, not seconds, and our 12 month warranty still applies. For ongoing supply, the PBS-33B with solder terminals stays in our range in six colours.

The PBS-33B 12mm momentary push button with two 20AWG leads already soldered on and sleeved in heat-shrink, so you can fit it and wire it straight into your project. It fits a 12mm panel hole, is rated 3A at 125V AC or 1A at 250V AC, and closes the circuit only while held down. Choose all-black leads or a red and black pair.

Specifications

ModelPBS-33B
Mounting12mm panel hole, threaded body with mounting nut
ActionMomentary, normally open (NO), closes while pressed
Rating3A at 125V AC / 1A at 250V AC
LeadsTwo pre-soldered 20AWG leads, about 12cm, stripped and tinned ends
Lead coloursBoth black, or one red and one black

What’s in the box

1×
PBS-33B push button with leads and mounting nut

One black button with the lead colours you select. Each quantity is one switch.

Great for

Arduino, ESP32 and Raspberry Pi input buttons
Reset and trigger buttons on project enclosures
Quick fits where you would rather not solder at the panel

Wiring & getting started

  1. Fit the switch

    Drill a 12mm hole. Remove the nut, feed the leads through the hole from the front, then refit the nut from behind and tighten.

  2. Connect a digital input

    With the board powered off, connect one lead to a digital input and the other to GND. The switch has no polarity, so either lead works on either side. For an Arduino input, enable INPUT_PULLUP.

  3. Check the response

    The input reads HIGH when released and LOW while pressed. Add software debouncing if one press registers more than once.

Note: Stay within 3A at 125V AC or 1A at 250V AC, and use a relay for anything heavier, such as a motor or pump. Any 230V mains wiring must be done by a licensed electrician.

Specification

Specification for PBS-33B 12mm Momentary Push Button, Pre-Wired - Clearance - Red and black
CLICK IT SKU CLICK-IT-967653
Brand NZN Electronics

Features

Clearance - final units. We are not restocking the pre-wired PBS-33B, so these last few are priced to clear. They are brand new, not seconds, and our 12 month warranty still applies. For ongoing supply, the PBS-33B with solder terminals stays in our range in…

  • Brand NZN Electronics

Reviews

No reviews yet.

Be the first to review this product and help other shoppers decide.

Do you own this product?

Only logged in customers who have purchased this product may leave a review.

Combo deals: buy together and save!

Add these products in one go - the total updates as you tick each item.

  • In stock $1.50
  • In stock $6.67
  • In stock $6.67
  • In stock $6.67

Related products

Related Promotions

View All Promotions