Skip to content
is here! Shop now, pay later in 4 easy installments

2.54mm Male Pin Header Strip 1×40 – Right Angle, Breakaway

Brand NZN Electronics CLICK IT SKU CLICK-IT-290545 Category Components

(0 reviews)

  • Brand NZN Electronics

Verified specifications

Screen
0.1 inch
Brand
NZN Electronics

Taken from this product's published details. If something is not listed here, it has not been verified.

Ask AI about this product

Answers use this product's information and the store's details. If it cannot be confirmed, it will point you to our team.

Any language. Press Enter to ask

Frequently bought together

Bundle idea: this item plus 1 recommended accessory/accessories, $2.08 in total. Add each item to the cart below.

Overview

A single-row male pin header with 40 right-angle pins at the standard 2.54mm (0.1 inch) spacing. Each pin is bent 90 degrees, so when the strip is soldered to a board the connector pins point out sideways, parallel to the board. That suits side-entry plugs such as a USB-to-serial adaptor, and connections that need to stay low inside an enclosure. It snaps to any length. For pins that stand straight up from the board, use the straight 1×40 header.

Specifications

Pins40 in one row (1×40)
Pitch2.54mm (0.1 inch)
Strip length101.6mm (40 x 2.54mm)
Pin styleRight angle, bent 90 degrees, square pins
MountingPlastic on the board, pins parallel to it
PlasticBlack, notched between every pin
BreakawaySnaps at any notch, no pins lost
Mates with2.54mm female headers and Dupont sockets
SolderingThrough-hole, hand solder

Datasheets

What’s in the box

1×
2.54mm 1×40 right-angle male header strip

One 40-pin strip per unit. Buy 5 or more for the bulk prices shown above.

Great for

A side-entry 6-pin serial header for a USB-to-serial adaptor
Connections at the edge of a board that sits flat in a case
Keeping a plug-in connection low under a lid or display
Plugging a small board in edge-on to a female header
Side connectors on your own PCB or stripboard
Replacing a damaged right-angle header on a module

Wiring & getting started

  1. Snap to length

    Count the pins you need, then bend the strip at the notch with flat-nose pliers or your fingers. It breaks cleanly between two pins. Side cutters work too if you cut in the notch, not through a pin.

  2. Fit it to the board

    Push the bent legs down through the holes from the top of the board, so the plastic sits flat on the board and the straight pins point out past the edge.

  3. Solder and check

    Solder one end leg from underneath, check the strip is flat and square to the edge, then solder the rest. Keep each joint quick so the plastic does not soften, and check for bridges between neighbouring pins.

  4. Connect

    Plug a female header or female Dupont jumper wires onto the pins from the side.

Note: the connector pins point sideways, so a module fitted with this header will not plug down into a breadboard. Use the straight version for that.

Specification

Specification for 2.54mm Male Pin Header Strip 1x40 - Right Angle, Breakaway
CLICK IT SKU CLICK-IT-290545
Brand NZN Electronics

Features

A single-row male pin header with 40 right-angle pins at the standard 2.54mm (0.1 inch) spacing. Each pin is bent 90 degrees, so when the strip is soldered to a board the connector pins point out sideways, parallel to the board. That suits side-entry plugs…

  • Brand NZN Electronics

Reviews

No reviews yet.

Be the first to review this product and help other shoppers decide.

Do you own this product?

Only logged in customers who have purchased this product may leave a review.

Combo deals: buy together and save!

Add these products in one go - the total updates as you tick each item.

  • In stock $0.81
  • In stock $6.67
  • In stock $6.67
  • In stock $6.67